Gaffer DeskMy shows

User guide

From empty rig to rolling in twelve steps.

Everything a new gaffer needs to run Gaffer Desk on set — patch, connect, light and roll.

  1. 01

    Create a show

    From the Shows page tap New show. Keep the sample rig ticked on your first try — it loads a SkyPanel, Vortex8, Orbiter, LS 600x and four Titan Tubes so you can explore every control before patching real lights.

  2. 02

    Patch your lights

    Open the Patch tab and tap Add light. Pick the brand, model and mode — the full official mode charts are built in (all 74 Creamsource Vortex modes, for example). The app shows the next free DMX address per universe, so dial that number into the fixture's menu.

  3. 03

    Run the bridge

    Browsers can't send DMX directly, so open the Bridge tab and download the Gaffer Desk Bridge. Run it on any laptop on set with plain Node (node gaffer-desk-bridge.mjs). It speaks Art-Net or sACN to your node or LumenRadio/CRMX transmitter.

  4. 04

    Connect

    On the Bridge tab, enter the bridge laptop's address and choose Art-Net or sACN. When the top bar says live, every fader move leaves the app over the network. Set sACN priority (main desk 150, backup 50) if two desks share a universe.

  5. 05

    Control the lights

    The Control tab shows a tile per light. Tap to select, then use the faders for intensity and CCT. Hold a tile for extra actions like Highlight — the light flashes full so you can find it on set.

  6. 06

    Color, wheel & gels

    The color section has three tabs: sliders for CCT/tint, a touch color Wheel for hue and saturation together, and a searchable Lee/Rosco Gel library. Tap Lee 204 Full CTO and every selected light takes that color.

  7. 07

    Effects

    Lightning, TV flicker, fire, police, paparazzi and faulty tube run in software, so they work on any fixture. The preset row above the grid gives one-tap looks — Campfire, Storm, Cop car — with tuned speed and depth.

  8. 08

    Groups, scenes & faders

    Select several lights and save them as a group for one-touch control. Save looks as scenes and fade between them. The Faders tab gives you group masters with hold-to-flash, like a real desk.

  9. 09

    Cues

    Record looks as cues in the Cues tab, set fade times and auto-follow, then fire them on action with the GO button. Undo/redo (the arrows in the top bar) covers every move.

  10. 10

    Set plan

    The Plan tab is a map of your stage. Drag each light to its real position, then switch to Control mode and tap lights by where they hang — no need to remember channel numbers.

  11. 11

    Share the show

    Tap the people button in the top bar and invite another gaffer by their Gaffer Desk email. They open the same show on their own iPad and every change syncs live both ways.

AsteraBox ART7 setup

ART7 takes DMX through a cable, not Bluetooth, so it needs a network node in front of it. Work through the checklist below before you call action.

AsteraBox ART7

Classic ART7 needs wired DMX input. Its AsteraApp Bluetooth connection is not Gaffer Desk’s TiMoTwo Bluetooth DMX connection.

  1. 1
    Gaffer Desk
    Browser · computer bridge
  2. 2
    DMX network node
    Art-Net/sACN → DMX OUT
  3. 3
    ART7 adapter
    5-pin XLR → 3.5 mm DMX IN
  4. 4
    ART7 → Astera lights
    CRMX wireless link

Quick fixes on set

  • Nothing responds: Check TX mode, the CRMX link, then start DMX output.
  • DMX indicator off: Gaffer Desk connected is not enough—check the node’s universe mapping and adapter.
  • Wrong colors or pixels: Match the exact fixture mode and start address to Patch.
  • One light missing: It may be linked to another transmitter—unlink and re-link it.

Connection checklist

0 of 6 checked · manual checks, not a connection test

  1. Connect the network node’s DMX OUT to Astera’s 5-pin XLR adapter, then plug its 3.5 mm end into ART7’s DMX input.

    • Node DMX OUT
    • 5-pin XLR adapter
    • ART7 3.5 mm DMX IN

    Confirm: The adapter is firmly connected at both ends.

    Missing a cable or DMX socket?

    Use Astera’s ART7 DMX adapter and an Art-Net/sACN-to-DMX node with a physical DMX output. A normal audio cable is not a substitute. ART7’s Micro-USB only charges the box.

  2. Charge or power ART7. Select transmitter (TX) mode using its controls and manufacturer manual.

    • Power on
    • TX indicator lit

    Confirm: The TX indicator is on.

    No power, or RX is showing?

    Check the charger and battery. If RX is showing, switch to TX following the ART7 manual. The DMX indicator can stay off until you start sending in step 5.

  3. Enable CRMX reception on your lights, then link them with ART7’s Link control according to its manual.

    • CRMX on at each light
    • Link confirmed

    Confirm: Each light confirms its CRMX link to ART7.

    A light will not link?

    Move the light closer, confirm its wireless receiver is enabled, and check whether it is already linked to another transmitter. Unlink only the intended receiver using its own manual, then try again.

  4. Match each light’s DMX mode and start address to Patch. Map the show universe to the node’s DMX output and enter the node’s IP in Gaffer Desk.

    • Node IP entered
    • Universe mapped
    • Modes match Patch

    Confirm: Protocol, universe, mode and addresses match.

    Unsure which IP or universe to use?

    Use the network node’s IP—not an ART7 address. Check the node’s output mapping. Gaffer Desk universe 1 may map to Art-Net 0 or 1; sACN uses the show’s universe number. Keep the node and sending device on a reachable network.

  5. Start output in the native iPad app, or connect the computer bridge in the browser version.

    • Gaffer Desk connected
    • ART7 DMX indicator lit

    Confirm: Gaffer Desk is connected and ART7’s DMX indicator is on.

    Connected, but the DMX indicator is off?

    A connected message alone does not prove DMX reception. Check the node’s input protocol, universe mapping, physical DMX output and adapter. On native iPad, allow Local Network access; in the browser, keep the computer bridge running.

  6. Raise one light gently, check color and individual pixels if supported, then test Blackout. Keep a physical safety control available.

    • One light responds
    • Blackout verified

    Confirm: The light responds correctly and Blackout works.

    Wrong colors, no pixels, or no brightness?

    Recheck the exact fixture mode and address against Patch, CRMX link, fixture level, group master, grand master and Blackout. Pixel controls need a compatible multi-pixel mode. If connection is lost, lights may hold their last look; use the physical safety control.

AsteraApp remains the tool for wireless fixture setup and battery monitoring. Direct Astera pairing and battery readback are not connected. If your label says ART7-WIFI, confirm that exact model before choosing a different connection.

Common questions

Ready to light?

Create a show with the sample rig and try every control risk-free.

Open my shows